Here after are presented some of the projects Enersole founder and general manager has taken part into in the past 13 years.
They highlight his experience that can be found in his resume.
ENERSOLE will be providing similar services among others.
Name of project: Kaptis and Bushangu hydropower plant project
Year: May to July 2017
Location: Kenya
Client: Kenya Power and Lighting Company (KPLC)
Main Project Features:
Kaptis: 3 units, installed capacity of 3x4,8 MW
Bushangu: 2 units, installed capacity of 1x3,6 MW + 1X1, 2MW
Position held: Power system engeneer
Activities performed: Audit of energy evacuation works design and review of load flow analysis of the 132KV and 33KV network.
Name of project: Mambilla hydropower plant project
Year: October to November 2016
Location: Nigeria
Client: Federal Ministry of Power
Main project features: 12 units, installed capacity of 6x200 MW
Position held: Power system engineer
Activities performed: Mambilla hydroelectric power plant energy evacuation works designing through a load flow analysis.
Name of project: Makai hydropower plant project
Year: July to October 2015
Location: Cameroon
Client: Platinum Power
Main project features: 4 vertical Francis turbines, installed capacity of 4x100 MW
Position held: Power system engineer
Activities performed: Integration studies of the hydroelectric power plant of Makai in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents and contingency analysis.
Software used: CYME
Name of project: Koukoutamba hydropower plant project
Year: May 2011 - July 2012
Location: GUINEA CONAKRY
Client: Organisation pour la Mise en Valeur du fleuve Sénégal (OMVS)
Main project features: 4 vertical Francis turbines, installed capacity 4x73,5MW
Position held: Design Engineer
Activities performed: Integration studies of the hydroelectric power plant of Koukoutamba in the interconnected electrical network of OMVS and OMVG
Software used: CYME
Name of Project: De Groene Delta Wind Farm Project
Year: July 2020
Location: Belgium
Client: Engie
Main Project Features: 2 x 3.5 MW Wind Farm
Positions held: Power System Engineer
Activities performed: Grid compliance study of Nordex 2 x 3.5 windmills in the Belgian grid
Software used: Power Factory
Name of Project: Greater Banjul Modernization project
Year: September 2018
Location: Gambia
Client: National Water and Electricity Company Limited (NAWEC)
Main Project Features: 225 kV transmission line between Brikama and Kotu substations (32 km)
Positions held: Power system engineer
Activities performed: Power system analysis of the Gambia High Voltage transmission system through a load flow, short circuit currents and contingency analysis.
Software used: Power Factory
Name of Project: Souapiti Hydropower plant project
Year: June 2018
Location: Guinea (Conakry)
Client: Administration et Contrôle des Grands Projet et Marchés Publics (ACGPMP)
Main Project Features: Souapiti: 4 units, installed capacity of 4 x 112 MW,
Positions held: Power system engineer
Activities performed: Integration studies of the hydroelectric power plant of Souapiti in the interconnected electrical network of Guinea through a load flow, short circuit currents, contingency analysis and transient stability analysis Checking of the need of generators to operate as synchronous condensers.
Software used: Power Factory
Name of Project: Stability study of the Guinean power system
Year: May 2018
Location: Guinea (Conakry)
Client: Administration et Contrôle des Grands Projet et Marchés Publics (ACGPMP)
Main Project Features: Entire power system stability analysis
Positions held: Power system engineer
Activities performed: Checking of transient stability studies of the Guinean interconnected electrical network through a load flow, short circuit currents, contingency analysis and transient stability analysis
Software used: Power Factory
Name of Project: Lot 3 - Resilience Feasibility study of the transmission system of DOMINICA
Year: June 2019
Location: DOMINICA
Client: French Development Agency (AFD)
Main Project Features: Resilience study of the transmission system
Positions held: Power System Engineer
Activities performed: Feasibility studies of the Dominican transmission system upgrade through a load flow, short circuit currents and contingency analysis.
Software used: PSS®E
Name of Project: SENELEC Protection plan stability study
Year: June 2020
Location: SENEGAL
Client: SENELEC (Senegalese utility)
Main Project Features: SENELEC power system protection plan study
Positions held: Power System Engineer
Activities performed: Audit of SENELEC PSS®E model with focus to transformers earthing systems modeling.
Software used: PSS®E
Name of Project: Dibamba power plant extension project
Year: February 2019
Location: Cameroon
Client: Dibamba Power Development Company
Main Project Features: Extension of existing 88 MW thermal power plant with additional 180 MW
Positions held: Power System Engineer
Activities performed: Integration studies of the extension of the Dibamba power plant into the Cameroon South Interconnected Network through a load flow, short circuit currents, contingency analysis and reactive margins determination at delivery point with CYME software.
Software used: CYME
Name of Project: Grand Eweng hydropower plant project
Year: 2016
Location: CAMEROON
Client: Hydromine (New York, United States)
Main Project Features: 6 units, installed capacity of 6x200 MW
Positions held: Power system engineer
Activities performed: Integration studies of the hydroelectric power plant of Grand Eweng in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents and contingency analysis.
Software used: CYME
Name of Project: MEMVE’ELE hydropower plant project
Year: 2014 - 2015
Location: CAMEROON
Client: MINEECAM (YAOUNDE - CAMEROON)
Main Project Features: 4 vertical Francis turbines, installed capacity of 4x52,75 MW
Positions held: Power System Engineer
Activities performed: Integration studies of the hydroelectric power plant of Memve’ele in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents analysis and transient stability analysis
Software used: CYME
Name of Project: ADJARALA hydropower plant project
Year: 2014
Location: BENIN
Client: COMMUNAUTE ELECTRIQUE DU BENIN (CEB) (Cotonou - BENIN)
Main Project Features: 3 vertical Francis turbines, installed capacity 3x49MW
Positions held: Project and power system engineer
Activities performed: Detailed design and tender documents of energy evacuation works (high voltage transmission lines and switchyards)
Integration studies of the hydroelectric power plant of Adjarala in the electrical network of CEB through a load flow analysis and assessment of units ability to work as synchronous condensersSoftware used: CYME
Name of Project: CLSG protection and defense plan
Year: July 2020
Location: Cote d’Ivoire, Liberia, Sierra Leone, Guinea
Client: Transco-CLSG
Main Project Features: Transmission system studies
Positions held: Power System Engineer
Activities performed: Activities performed: Load flow and voltage compensation analysis studies for the different sequences of commissioning of CLSG system
Software used: SMARTFLOW/EUROSTAG
Name of Project: OMVS floating PV Project
Year: January 2020
Location: Mali, Mauritania, Senegal
Client: OMVS ( Organisation pour la Mise en Valeur du fleuve Sénégal)
Main Project Features: Floating PV plant of 200 MW on a hydro power plant dam reservoir
Positions held: Power System Engineer
Activities performed: Integration studies of a 200 MW floating PV plant on hydro power plant dam reservoir (static and dynamic studies)
Software used: SMARTFLOW/EUROSTAG
Name of Project: KOSSOU PV Project
Year: November 2019 -December 2019
Location: Ivory Coast
Client: CI-ENERGIES
Main Project Features: Floating PV plant of 20 MW on the KOSSOU hydro power plant dam reservoir
Positions held: Power System Engineer
Activities performed: Integration studies of a 20 MW floating PV plant on the KOSSOU hydro power plant dam reservoir (static and dynamic studies)
Software used: SMARTFLOW/EUROSTAG
Name of Project: Gridlink interconnection Project
Year: October 2019
Location: France/United Kingdom
Client: Baringa Partners
Main Project Features: HVDC interconnection transmission line of 525 kV between France and United Kingdom (156 km-1400 MW)
Positions held: Power System Engineer
Activities performed: DC Load flow and reliability analysis (B5 and B6 indicators calculation related to grid losses variation and security of supply respectively) with SCANNER software
Software used: SCANNER
Name of Project: Burkina Faso system stability study for integration of renewable energy
Year: May to November 2019
Location: BURKINA FASO
Client: Ministry of Energy (PASEL)
Main Project Features: National interconnected network
Positions held: Power System Engineer
Activities performed: Probabilistic studies of Burkina Faso national network with the integration of photovoltaic power plants Assessment of load curtailment, spinning reserve, generation costs and network constraints
Software used: SCANNER, SMARTFLOW/EUROSTAG
Name of Project: Ghoubet Wind Farm
Year: June 2019
Location: DJIBOUTI
Client: EDD (Electricité de Djibouti)
Main Project Features: Ghoubet Wind Farm: 58.9 MW
Positions held: Power System Engineer
Activities performed: Probabilistic integration studies of Ghoubet Wind Farm in the Djiboutian grid with load curtailment and spinning reserve assessment
Software used: SCANNER
Name of Project: Nigeria-Benin interconnection Project
Year: March 2019
Location: Nigeria/Benin
Client: West African Power Pool (WAPP)
Main Project Features: Interconnection transmission lines of 330 kV between Nigeria (Ajegunle) and Benin (Onigbolo) (78 km)
Positions held: Power System Engineer
Activities performed: Load flow, short circuit currents and contingency analysis with EUROSTAG software
Software used: SMARTFLOW/EUROSTAG
Name of project: Kaptis and Bushangu hydropower plant project
Year: May to July 2017
Location: Kenya
Client: Kenya Power and Lighting Company (KPLC)
Main Project Features:
Kaptis: 3 units, installed capacity of 3x4,8 MW
Bushangu: 2 units, installed capacity of 1x3,6 MW + 1X1, 2MW
Position held: Power system engeneer
Activities performed: Audit of energy evacuation works design and review of load flow analysis of the 132KV and 33KV network.
Name of project: Mambilla hydropower plant project
Year: October to November 2016
Location: Nigeria
Client: Federal Ministry of Power
Main project features: 12 units, installed capacity of 6x200 MW
Position held: Power system engineer
Activities performed: Mambilla hydroelectric power plant energy evacuation works designing through a load flow analysis.
Name of project: Makai hydropower plant project
Year: July to October 2015
Location: Cameroon
Client: Platinum Power
Main project features: 4 vertical Francis turbines, installed capacity of 4x100 MW
Position held: Power system engineer
Activities performed: Integration studies of the hydroelectric power plant of Makai in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents and contingency analysis.
Software used: CYME
Name of project: Koukoutamba hydropower plant project
Year: May 2011 - July 2012
Location: GUINEA CONAKRY
Client: Organisation pour la Mise en Valeur du fleuve Sénégal (OMVS)
Main project features: 4 vertical Francis turbines, installed capacity 4x73,5MW
Position held: Design Engineer
Activities performed: Integration studies of the hydroelectric power plant of Koukoutamba in the interconnected electrical network of OMVS and OMVG
Software used: CYME
Name of Project: De Groene Delta Wind Farm Project
Year: July 2020
Location: Belgium
Client: Engie
Main Project Features: 2 x 3.5 MW Wind Farm
Positions held: Power System Engineer
Activities performed: Grid compliance study of Nordex 2 x 3.5 windmills in the Belgian grid
Software used: Power Factory
Name of Project: Greater Banjul Modernization project
Year: September 2018
Location: Gambia
Client: National Water and Electricity Company Limited (NAWEC)
Main Project Features: 225 kV transmission line between Brikama and Kotu substations (32 km)
Positions held: Power system engineer
Activities performed: Power system analysis of the Gambia High Voltage transmission system through a load flow, short circuit currents and contingency analysis.
Software used: Power Factory
Name of Project: Souapiti Hydropower plant project
Year: June 2018
Location: Guinea (Conakry)
Client: Administration et Contrôle des Grands Projet et Marchés Publics (ACGPMP)
Main Project Features: Souapiti: 4 units, installed capacity of 4 x 112 MW,
Positions held: Power system engineer
Activities performed: Integration studies of the hydroelectric power plant of Souapiti in the interconnected electrical network of Guinea through a load flow, short circuit currents, contingency analysis and transient stability analysis Checking of the need of generators to operate as synchronous condensers.
Software used: Power Factory
Name of Project: Stability study of the Guinean power system
Year: May 2018
Location: Guinea (Conakry)
Client: Administration et Contrôle des Grands Projet et Marchés Publics (ACGPMP)
Main Project Features: Entire power system stability analysis
Positions held: Power system engineer
Activities performed: Checking of transient stability studies of the Guinean interconnected electrical network through a load flow, short circuit currents, contingency analysis and transient stability analysis
Software used: Power Factory
Name of Project: Lot 3 - Resilience Feasibility study of the transmission system of DOMINICA
Year: June 2019
Location: DOMINICA
Client: French Development Agency (AFD)
Main Project Features: Resilience study of the transmission system
Positions held: Power System Engineer
Activities performed: Feasibility studies of the Dominican transmission system upgrade through a load flow, short circuit currents and contingency analysis.
Software used: PSS®E
Name of Project: SENELEC Protection plan stability study
Year: June 2020
Location: SENEGAL
Client: SENELEC (Senegalese utility)
Main Project Features: SENELEC power system protection plan study
Positions held: Power System Engineer
Activities performed: Audit of SENELEC PSS®E model with focus to transformers earthing systems modeling.
Software used: PSS®E
Name of Project: Dibamba power plant extension project
Year: February 2019
Location: Cameroon
Client: Dibamba Power Development Company
Main Project Features: Extension of existing 88 MW thermal power plant with additional 180 MW
Positions held: Power System Engineer
Activities performed: Integration studies of the extension of the Dibamba power plant into the Cameroon South Interconnected Network through a load flow, short circuit currents, contingency analysis and reactive margins determination at delivery point with CYME software.
Software used: CYME
Name of Project: Grand Eweng hydropower plant project
Year: 2016
Location: CAMEROON
Client: Hydromine (New York, United States)
Main Project Features: 6 units, installed capacity of 6x200 MW
Positions held: Power system engineer
Activities performed: Integration studies of the hydroelectric power plant of Grand Eweng in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents and contingency analysis.
Software used: CYME
Name of Project: MEMVE’ELE hydropower plant project
Year: 2014 - 2015
Location: CAMEROON
Client: MINEECAM (YAOUNDE - CAMEROON)
Main Project Features: 4 vertical Francis turbines, installed capacity of 4x52,75 MW
Positions held: Power System Engineer
Activities performed: Integration studies of the hydroelectric power plant of Memve’ele in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents analysis and transient stability analysis
Software used: CYME
Name of Project: ADJARALA hydropower plant project
Year: 2014
Location: BENIN
Client: COMMUNAUTE ELECTRIQUE DU BENIN (CEB) (Cotonou - BENIN)
Main Project Features: 3 vertical Francis turbines, installed capacity 3x49MW
Positions held: Project and power system engineer
Activities performed: Detailed design and tender documents of energy evacuation works (high voltage transmission lines and switchyards)
Integration studies of the hydroelectric power plant of Adjarala in the electrical network of CEB through a load flow analysis and assessment of units ability to work as synchronous condensersSoftware used: CYME
Name of Project: CLSG protection and defense plan
Year: July 2020
Location: Cote d’Ivoire, Liberia, Sierra Leone, Guinea
Client: Transco-CLSG
Main Project Features: Transmission system studies
Positions held: Power System Engineer
Activities performed: Activities performed: Load flow and voltage compensation analysis studies for the different sequences of commissioning of CLSG system
Software used: SMARTFLOW/EUROSTAG
Name of Project: OMVS floating PV Project
Year: January 2020
Location: Mali, Mauritania, Senegal
Client: OMVS ( Organisation pour la Mise en Valeur du fleuve Sénégal)
Main Project Features: Floating PV plant of 200 MW on a hydro power plant dam reservoir
Positions held: Power System Engineer
Activities performed: Integration studies of a 200 MW floating PV plant on hydro power plant dam reservoir (static and dynamic studies)
Software used: SMARTFLOW/EUROSTAG
Name of Project: KOSSOU PV Project
Year: November 2019 -December 2019
Location: Ivory Coast
Client: CI-ENERGIES
Main Project Features: Floating PV plant of 20 MW on the KOSSOU hydro power plant dam reservoir
Positions held: Power System Engineer
Activities performed: Integration studies of a 20 MW floating PV plant on the KOSSOU hydro power plant dam reservoir (static and dynamic studies)
Software used: SMARTFLOW/EUROSTAG
Name of Project: Gridlink interconnection Project
Year: October 2019
Location: France/United Kingdom
Client: Baringa Partners
Main Project Features: HVDC interconnection transmission line of 525 kV between France and United Kingdom (156 km-1400 MW)
Positions held: Power System Engineer
Activities performed: DC Load flow and reliability analysis (B5 and B6 indicators calculation related to grid losses variation and security of supply respectively) with SCANNER software
Software used: SCANNER
Name of Project: Burkina Faso system stability study for integration of renewable energy
Year: May to November 2019
Location: BURKINA FASO
Client: Ministry of Energy (PASEL)
Main Project Features: National interconnected network
Positions held: Power System Engineer
Activities performed: Probabilistic studies of Burkina Faso national network with the integration of photovoltaic power plants Assessment of load curtailment, spinning reserve, generation costs and network constraints
Software used: SCANNER, SMARTFLOW/EUROSTAG
Name of Project: Ghoubet Wind Farm
Year: June 2019
Location: DJIBOUTI
Client: EDD (Electricité de Djibouti)
Main Project Features: Ghoubet Wind Farm: 58.9 MW
Positions held: Power System Engineer
Activities performed: Probabilistic integration studies of Ghoubet Wind Farm in the Djiboutian grid with load curtailment and spinning reserve assessment
Software used: SCANNER
Name of Project: Nigeria-Benin interconnection Project
Year: March 2019
Location: Nigeria/Benin
Client: West African Power Pool (WAPP)
Main Project Features: Interconnection transmission lines of 330 kV between Nigeria (Ajegunle) and Benin (Onigbolo) (78 km)
Positions held: Power System Engineer
Activities performed: Load flow, short circuit currents and contingency analysis with EUROSTAG software
Software used: SMARTFLOW/EUROSTAG
Name of project: Kaptis and Bushangu hydropower plant project
Year: May to July 2017
Location: Kenya
Client: Kenya Power and Lighting Company (KPLC)
Main Project Features:
Kaptis: 3 units, installed capacity of 3x4,8 MW
Bushangu: 2 units, installed capacity of 1x3,6 MW + 1X1, 2MW
Position held: Power system engeneer
Activities performed: Audit of energy evacuation works design and review of load flow analysis of the 132KV and 33KV network.
Name of project: Mambilla hydropower plant project
Year: October to November 2016
Location: Nigeria
Client: Federal Ministry of Power
Main project features: 12 units, installed capacity of 6x200 MW
Position held: Power system engineer
Activities performed: Mambilla hydroelectric power plant energy evacuation works designing through a load flow analysis.
Name of project: Makai hydropower plant project
Year: July to October 2015
Location: Cameroon
Client: Platinum Power
Main project features: 4 vertical Francis turbines, installed capacity of 4x100 MW
Position held: Power system engineer
Activities performed: Integration studies of the hydroelectric power plant of Makai in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents and contingency analysis.
Software used: CYME
Name of project: Koukoutamba hydropower plant project
Year: May 2011 - July 2012
Location: GUINEA CONAKRY
Client: Organisation pour la Mise en Valeur du fleuve Sénégal (OMVS)
Main project features: 4 vertical Francis turbines, installed capacity 4x73,5MW
Position held: Design Engineer
Activities performed: Integration studies of the hydroelectric power plant of Koukoutamba in the interconnected electrical network of OMVS and OMVG
Software used: CYME
Name of Project: SOUBRE hydropower plant project
Year: 2008
Location: IVORY COAST
Client: CI-Energies ABIDJAN-PLATEAU (Abidjan - IVORY COAST)
Main Project Features: SOUBRE hydropower plant project
Positions held: Design Engineer
Activities performed: Substation Electrical network single line diagram update
Name of Project: AMAILA FALLS Hydropower Plant Project
Year: 2008
Location: BRAZIL
Client: ANDRITZ HYDRO Inepar do Brasil S.A. (Barueri - São Paulo - BRAZIL)
Main Project Features: AMAILA FALLS Hydropower Plant study
Positions held: Design Engineer
Activities performed: Analysis of the generators electromagnetic parameters influence on the network stability
Name of Project: Rural province of Guidimakha Xéri Kofo photovoltaic power plant project
Year: 2008
Location: MALI
Client: Association du Village de Sansangué pour le Développement
Main Project Features: Electrifications of the rural province of Guidmakha Xéri Kofo in Mali
Positions held: Project Manager
Activities performed: Designing of a photovoltaic power plant in an isolated network
Name of Project: Industrial project study
Year: 2006
Location: FRANCE
Client: Windspectra
Main Project Features: Study of a windmill farm electrical losses
Positions held: Student
Activities performed: Creation of a software calculating windmill electrical losses according to the wind speed
Name of Project: Tanjung Sakti HPP Project
Year: 2017
Location: Indonesia
Client: PT Indonesia Power
Main Project Features: hydroelectic power plant of 3 x 40 MW
Positions held: Project Engineer
Activities performed: Integration studies of Tanjung Sakti HPP: Design of HV transmission lines and switchyards, Power system analysis, Costs estimation of energy evacuation works
Name of Project: Nam Lik hydropower plant project
Year: 2017
Location: LAOS
Client: Nam Lik 1 Power Company
Main Project Features: 2 horizontal bulb turbines, installed capacity 2x32,5 MW
Positions held: Project Engineer
Activities performed: Review of earthing system calculation notes
Name of Project: Montagne d’Or transmission line project
Year: 2016
Location: FRENCH GUIANA
Client: Nord Gold
Main Project Features: 1 transmission line of 90kV, 120km (Citron – St Laurent du Maroni)
Positions held: Project Engineer
Activities performed: Prefeasibility and feasibility study of energy evacuation works with the electrical designing of transmission line (cross-section calculation under thermal, short-circuit, voltage drop and corona effect criterion, determination of economical cross-section)
Name of Project: Nam Theun hydropower plant project
Year: 2016
Location: LAOS
Client: Electricity Generating Public Company Limited (EGCO)
Main Project Features: 3 vertical Francis turbines, installed capacity 2x265 MW+1x133 MW
Positions held: Project Engineer
Activities performed: Due diligence related to the hydroelectric power plants energy evacuation works designing. Review of 500 kV and 115 kV switchyards and transmission lines design
Name of Project: Kandadji hydropower plant project
Year: 2016
Location: NIGER
Client: Haut-Commissariat à l’Aménagement de la Vallée du Niger (HCAVN)
Main Project Features: 4 vertical Kaplan turbines, installed capacity 4x32MW
Positions held: Project Engineer
Activities performed: Detailed design and tender documents specification for energy evacuation works (132kV transmission lines and 132kV/33kV switchyard)
Name of Project: 3 mini hydropower plants projects in Liberia (Gbedin falls, Ya Creek, River Gee)
Year: 2016
Location: LIBERIA
Client: African Development Bank and Rural and Renewable Energy Agency (ADB AND RREA)
Main Project Features: 3 mini hydropower plant projects and associated transmission lines
Positions held: Project Engineer
Activities performed: Feasibility study of the 3 mini hydropower plants and associated transmission lines (30kV, 66kV)
Name of Project: Mong Hsat hydropower plant project
Year: 2016
Location: MYANMAR
Client: Suntac Power
Main Project Features: 2 units, installed capacity 2x16MW
Positions held: Project Engineer
Activities performed: Feasibility study of energy evacuation works (33kV, 66kV and 132kV transmission lines and 132kV/33kV switchyards)
Name of Project: FARKWA pumping station project
Year: 2015
Location: TANZANIA
Client: MINISTRY OF WATER (Dar es Salaam - TANZANIA)
Main Project Features: 6 pumping units, installed capacity 6x1,5MW
Positions held: Project Engineer
Activities performed: Detailed design and tender documents of the pumping station electrical systems
Name of Project: PWALUGU hydropower plant project
Year: 2015
Location: GHANA
Client: VOLTA RIVER AUTHORITY (ACCRA - GHANA)
Main Project Features: Installed capacity 3x30MW
Positions held: Project Engineer
Activities performed: Feasibility studies of powerhouse electrical auxiliaries and energy evacuation works (161kV transmission lines and switchyard)
Name of Project: 4 mini hydropower plant projects
Year: 2014 - 2015
Location: GUINEA
Client: ADMINISTRATION ET CONTROLE DES GRANDS PROJETS PUBLICS (ACGP) (Conakry - GUINEA)
Main Project Features: 4 mini hydropower plant projects, installed capacity of 2x3,15MVA, 3x1,25MVA, 2x24,5MVA, 2x15MVA
Positions held: Project Engineer
Activities performed: Detailed design and tender documents of energy evacuation works (high voltage transmission lines and switchyards)
Name of Project: MEMVE’ELE hydropower plant project
Year: 2014 - 2015
Location: CAMEROON
Client: MINEECAM (YAOUNDE - CAMEROON)
Main Project Features: 4 vertical Francis turbines, installed capacity of 4x52,75 MW
Activities performed: Integration studies of the hydroelectric power plant of Memve’ele in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents analysis and transient stability analysis
Name of Project: ARTIBONITE 4C hydropower plant project
Year: 2014
Location: HAITI
Client: SINOHYDRO CORPORATION LTD (Beijing - CHINA)
Main Project Features: installed capacity 2x16MW
Positions held: Project Engineer
Activities performed: Feasibility study of energy evacuation works (high voltage transmission lines and switchyards)
Name of project: ADJARALA hydropower plant project
Year: 2014
Location: Benin
Client: Communauté électrique du Bénin (CEB)
Main Project Features: 3 vertical Francis turbines, installed capacity 3x49MW
Position held: Project Engineer
Activities: Detailed design and tender documents of energy evacuation works (high voltage transmission lines and switchyards)
Name of Project: KOUKOUTAMBA hydropower plant project
Year: 2011-2012
Location: GUINEA
Client: Organisation pour la Mise en Valeur du Fleuve Sénégal (Dakar - SENEGAL)
Main Project Features: 4 vertical Francis turbines, installed capacity 4x73,5MW
Positions held: Design Engineer
Activities performed: Energy evacuation works feasibility and detailed design studies coordination (high voltage transmission lines, high voltage switchyards)
Name of Project: ANDEKALEKA hydropower plant project
Year: 2009 - 2010
Location: MADAGASCAR
Client: JIRAMA (Antananarivo - MADAGASCAR)
Main Project Features: Power plant extension works with two additional units G3 and G4, 2 vertical Francis turbines, total rated output of 76 MW
Positions held: Design Engineer
Activities performed: Checking of the generators technical specifications. Checking of the generators drawings. Checking of generators windings bars Factory Acceptance Tests results
Name of Project: DISI MUDAWARRA water transfer project
Year: 2009
Location: JORDAN
Client: Gama Enerji (ANKARA - TURKEY)
Main Project Features: water transfer project from Disi Mudawarra to Amman
Positions held: Design Engineer
Activities performed: Pumping station transmission lines electrical losses calculation
Name of Project: GRAND POUBARA hydropower plant project
Year : February- November 2009
Main Project Features : 4 vertical Francis turbines, installed capacity of 4x40 MW
Position held : Design Engineer
Activities performed : Units short circuit currents assessment
Name of Project: MACAGUA II hydropower plant project
Year: 2008
Location: VENEZUELA
Client: Electrificacion del Caroni
Main Project Features: 2 Kaplan turbines, installed capacity of 86 MW
Positions held: Design Engineer
Activities performed: Checking of the generators technical specifications. Designing of technical room air heaters
Name of Project: MARCONI hydropower plant project
Year: 2008
Client: Studio Frosio
Main Project Features: 2 Kaplan turbines, installed capacity of 32 MW
Positions held: Design Engineer
Activities performed: Designing of the generators and heat exchangers
Name of Project: SOUBRE hydropower plant project
Year: 2008
Location: IVORY COAST
Client: CI-Energies ABIDJAN-PLATEAU (Abidjan - IVORY COAST)
Main Project Features: SOUBRE hydropower plant project
Positions held: Design Engineer
Activities performed: Substation Electrical network single line diagram update
Name of Project: AMAILA FALLS Hydropower Plant Project
Year: 2008
Location: BRAZIL
Client: ANDRITZ HYDRO Inepar do Brasil S.A. (Barueri - São Paulo - BRAZIL)
Main Project Features: AMAILA FALLS Hydropower Plant study
Positions held: Design Engineer
Activities performed: Analysis of the generators electromagnetic parameters influence on the network stability
Name of Project: Rural province of Guidimakha Xéri Kofo photovoltaic power plant project
Year: 2008
Location: MALI
Client: Association du Village de Sansangué pour le Développement
Main Project Features: Electrifications of the rural province of Guidmakha Xéri Kofo in Mali
Positions held: Project Manager
Activities performed: Designing of a photovoltaic power plant in an isolated network
Name of Project: Industrial project study
Year: 2006
Location: FRANCE
Client: Windspectra
Main Project Features: Study of a windmill farm electrical losses
Positions held: Student
Activities performed: Creation of a software calculating windmill electrical losses according to the wind speed
Name of Project: Tanjung Sakti HPP Project
Year: 2017
Location: Indonesia
Client: PT Indonesia Power
Main Project Features: hydroelectic power plant of 3 x 40 MW
Positions held: Project Engineer
Activities performed: Integration studies of Tanjung Sakti HPP: Design of HV transmission lines and switchyards, Power system analysis, Costs estimation of energy evacuation works
Name of Project: Nam Lik hydropower plant project
Year: 2017
Location: LAOS
Client: Nam Lik 1 Power Company
Main Project Features: 2 horizontal bulb turbines, installed capacity 2x32,5 MW
Positions held: Project Engineer
Activities performed: Review of earthing system calculation notes
Name of Project: Montagne d’Or transmission line project
Year: 2016
Location: FRENCH GUIANA
Client: Nord Gold
Main Project Features: 1 transmission line of 90kV, 120km (Citron – St Laurent du Maroni)
Positions held: Project Engineer
Activities performed: Prefeasibility and feasibility study of energy evacuation works with the electrical designing of transmission line (cross-section calculation under thermal, short-circuit, voltage drop and corona effect criterion, determination of economical cross-section)
Name of Project: Nam Theun hydropower plant project
Year: 2016
Location: LAOS
Client: Electricity Generating Public Company Limited (EGCO)
Main Project Features: 3 vertical Francis turbines, installed capacity 2x265 MW+1x133 MW
Positions held: Project Engineer
Activities performed: Due diligence related to the hydroelectric power plants energy evacuation works designing. Review of 500 kV and 115 kV switchyards and transmission lines design
Name of Project: Kandadji hydropower plant project
Year: 2016
Location: NIGER
Client: Haut-Commissariat à l’Aménagement de la Vallée du Niger (HCAVN)
Main Project Features: 4 vertical Kaplan turbines, installed capacity 4x32MW
Positions held: Project Engineer
Activities performed: Detailed design and tender documents specification for energy evacuation works (132kV transmission lines and 132kV/33kV switchyard)
Name of Project: 3 mini hydropower plants projects in Liberia (Gbedin falls, Ya Creek, River Gee)
Year: 2016
Location: LIBERIA
Client: African Development Bank and Rural and Renewable Energy Agency (ADB AND RREA)
Main Project Features: 3 mini hydropower plant projects and associated transmission lines
Positions held: Project Engineer
Activities performed: Feasibility study of the 3 mini hydropower plants and associated transmission lines (30kV, 66kV)
Name of Project: Mong Hsat hydropower plant project
Year: 2016
Location: MYANMAR
Client: Suntac Power
Main Project Features: 2 units, installed capacity 2x16MW
Positions held: Project Engineer
Activities performed: Feasibility study of energy evacuation works (33kV, 66kV and 132kV transmission lines and 132kV/33kV switchyards)
Name of Project: FARKWA pumping station project
Year: 2015
Location: TANZANIA
Client: MINISTRY OF WATER (Dar es Salaam - TANZANIA)
Main Project Features: 6 pumping units, installed capacity 6x1,5MW
Positions held: Project Engineer
Activities performed: Detailed design and tender documents of the pumping station electrical systems
Name of Project: PWALUGU hydropower plant project
Year: 2015
Location: GHANA
Client: VOLTA RIVER AUTHORITY (ACCRA - GHANA)
Main Project Features: Installed capacity 3x30MW
Positions held: Project Engineer
Activities performed: Feasibility studies of powerhouse electrical auxiliaries and energy evacuation works (161kV transmission lines and switchyard)
Name of Project: 4 mini hydropower plant projects
Year: 2014 - 2015
Location: GUINEA
Client: ADMINISTRATION ET CONTROLE DES GRANDS PROJETS PUBLICS (ACGP) (Conakry - GUINEA)
Main Project Features: 4 mini hydropower plant projects, installed capacity of 2x3,15MVA, 3x1,25MVA, 2x24,5MVA, 2x15MVA
Positions held: Project Engineer
Activities performed: Detailed design and tender documents of energy evacuation works (high voltage transmission lines and switchyards)
Name of Project: MEMVE’ELE hydropower plant project
Year: 2014 - 2015
Location: CAMEROON
Client: MINEECAM (YAOUNDE - CAMEROON)
Main Project Features: 4 vertical Francis turbines, installed capacity of 4x52,75 MW
Activities performed: Integration studies of the hydroelectric power plant of Memve’ele in the southern interconnected electrical network of Cameroon through a load flow, short circuit currents analysis and transient stability analysis
Name of Project: ARTIBONITE 4C hydropower plant project
Year: 2014
Location: HAITI
Client: SINOHYDRO CORPORATION LTD (Beijing - CHINA)
Main Project Features: installed capacity 2x16MW
Positions held: Project Engineer
Activities performed: Feasibility study of energy evacuation works (high voltage transmission lines and switchyards)
Name of project: ADJARALA hydropower plant project
Year: 2014
Location: Benin
Client: Communauté électrique du Bénin (CEB)
Main Project Features: 3 vertical Francis turbines, installed capacity 3x49MW
Position held: Project Engineer
Activities: Detailed design and tender documents of energy evacuation works (high voltage transmission lines and switchyards)
Name of Project: KOUKOUTAMBA hydropower plant project
Year: 2011-2012
Location: GUINEA
Client: Organisation pour la Mise en Valeur du Fleuve Sénégal (Dakar - SENEGAL)
Main Project Features: 4 vertical Francis turbines, installed capacity 4x73,5MW
Positions held: Design Engineer
Activities performed: Energy evacuation works feasibility and detailed design studies coordination (high voltage transmission lines, high voltage switchyards)
Name of Project: ANDEKALEKA hydropower plant project
Year: 2009 - 2010
Location: MADAGASCAR
Client: JIRAMA (Antananarivo - MADAGASCAR)
Main Project Features: Power plant extension works with two additional units G3 and G4, 2 vertical Francis turbines, total rated output of 76 MW
Positions held: Design Engineer
Activities performed: Checking of the generators technical specifications. Checking of the generators drawings. Checking of generators windings bars Factory Acceptance Tests results
Name of Project: DISI MUDAWARRA water transfer project
Year: 2009
Location: JORDAN
Client: Gama Enerji (ANKARA - TURKEY)
Main Project Features: water transfer project from Disi Mudawarra to Amman
Positions held: Design Engineer
Activities performed: Pumping station transmission lines electrical losses calculation
Name of Project: GRAND POUBARA hydropower plant project
Year : February- November 2009
Main Project Features : 4 vertical Francis turbines, installed capacity of 4x40 MW
Position held : Design Engineer
Activities performed : Units short circuit currents assessment
Name of Project: MACAGUA II hydropower plant project
Year: 2008
Location: VENEZUELA
Client: Electrificacion del Caroni
Main Project Features: 2 Kaplan turbines, installed capacity of 86 MW
Positions held: Design Engineer
Activities performed: Checking of the generators technical specifications. Designing of technical room air heaters
Name of Project: MARCONI hydropower plant project
Year: 2008
Client: Studio Frosio
Main Project Features: 2 Kaplan turbines, installed capacity of 32 MW
Positions held: Design Engineer
Activities performed: Designing of the generators and heat exchangers
Name of Project: SOUBRE hydropower plant project
Year: 2008
Location: IVORY COAST
Client: CI-Energies ABIDJAN-PLATEAU (Abidjan - IVORY COAST)
Main Project Features: SOUBRE hydropower plant project
Positions held: Design Engineer
Activities performed: Substation Electrical network single line diagram update
Name of Project: AMAILA FALLS Hydropower Plant Project
Year: 2008
Location: BRAZIL
Client: ANDRITZ HYDRO Inepar do Brasil S.A. (Barueri - São Paulo - BRAZIL)
Main Project Features: AMAILA FALLS Hydropower Plant study
Positions held: Design Engineer
Activities performed: Analysis of the generators electromagnetic parameters influence on the network stability
Name of Project: Rural province of Guidimakha Xéri Kofo photovoltaic power plant project
Year: 2008
Location: MALI
Client: Association du Village de Sansangué pour le Développement
Main Project Features: Electrifications of the rural province of Guidmakha Xéri Kofo in Mali
Positions held: Project Manager
Activities performed: Designing of a photovoltaic power plant in an isolated network
Name of Project: Industrial project study
Year: 2006
Location: FRANCE
Client: Windspectra
Main Project Features: Study of a windmill farm electrical losses
Positions held: Student
Activities performed: Creation of a software calculating windmill electrical losses according to the wind speed
Name of Project: KOUKOUTAMBA hydropower plant project
Year: 2011-2012
Location: GUINEA
Client:: Organisation pour la Mise en Valeur du Fleuve Sénégal (Dakar - SENEGAL)
Main Project Features: 4 vertical Francis turbines, installed capacity 4x73,5MW
Positions held: Design Engineer
Activities performed: Establishment of bidding documents technical specifications and bill of quantities
Name of Project: JIRAU hydropower plant project
Year: 2009 - 2010
Location: BRAZIL, CHINA
Client:: ESBR (Belo Horizonte - BRAZIL)
Main Project Features: horizontal bulb turbines, installed capacity 44x76,5MW
Positions held: Design Engineer
Activities performed: Generators excitation system Factory Acceptance Test in Dong Feng’s factory in Chengdu in China.
Checking of generators drawings and calculation reports.
Name of Project: GURARA Hydropower Plant
Year: 2008 - 2010
Location: NIGERIA
Client:: FEDERAL MINISTRY OF WATER RESOURCES (Abuja - NIGERIA)
Main Project Features: 3 vertical Kaplan turbines, installed capacity 3x30 MW
Positions held: Design Engineer
Activities performed: Supervision of the erection works and units partial commissioning tests
Name of Project: NANGBETO hydropower plant project
Year: 2008
Location: BENIN
Client:: Communauté Electrique du Bénin (CEB)
Main Project Features: Rehabilitation of the generators voltage and speed regulators
Positions held: Design Engineer
Activities performed: Establishment of voltage and speed regulators technical specifications of the tender documents
Name of Project: Manantali hydropower plant project
Year: 2016 - 2017
Location: MALI
Client: Société de Gestion de l’Energie de Manantali (SOGEM)
Main Project Features: 5 vertical Kaplan turbines, installed capacity 5x40 MW
Positions held: Project Engineer
Activities performed: Supervision of overhaul and re-commissioning of units 1,2,4 and 5
Name of Project: Project of the Electricity Sector Strengthening in Ivory Coast (PRSECI) project
Year: March 2015
Location: IVORY COAST
Client: Société des Énergies de Côte d’Ivoire (CI-ENERGIES)
Main Project Features: Supervision and control of Ivory Coast electrical networks strengthening works
Positions held: Project Engineer
Activities performed: Owner’s Engineer:
Name of Project: DEVOLL hydropower plant project
Year: 2014
Location: ALBANIA
Client:: DEVOLL HYDROPOWER (TIRANA - ALBANIA)
Main Project Features: Installed capacity of 39 MW
Positions held: Project Engineer
Activities performed: Factory Acceptance tests on 220kV circuit breaker of Moglicë switchyard in Alstom grid’s factory in Villeurbanne in France
Name of Project: Kaleta hydropower plant project
Year: August 2012 - August 2013
Location: GUINEA CONAKRY
Client:: Administration et Control des Grands Projets (ACGP)
Main Project Features: 3 vertical Francis turbines, installed capacity of 3x70 MW
Positions held: Project Engineer
Activities performed : Technical assistance to the Client
Name of Project: INGA hydropower plant project - FRIPT
Year: 2013
Location: CONGO (DEM. REP.)
Client:: CONGO ENERGIE (KINSHASA - CONGO (DEM. REP.))
Main Project Features: Overhaul of unit G27 and G28, installed capacity 2x174MW
Positions held: Project Engineer
Activities performed: Analysis of bidders’ proposals regarding units electrical systems
Name of Project: SHIRORO hydropower plant project
Year: December 2010 – March 2012
Location: NIGERIA
Client:: Power Holding Company of Nigeria ( PHCN)
Main Project Features: 4 vertical Francis turbines, installed capacity of 4x150 MW
Positions held: Project Manager
Activities performed:
Name of Project: GIBE III Hydropower plant project
Year: 2009 - 2012
Location: ETHIOPIA
Client:: EEPCO (Addis Ababa - ETHIOPIA)
Main Project Features: 10 vertical Francis turbines, installed capacity of 10x187 MW
Positions held: Design Engineer
Activities performed: Technical coordination of the electromechanical experts staff (around 10) in charge of construction drawings approbation
Name of Project: Flood wall of the TIHANGE nuclear power plant
Year: 2011 - 2012
Location: BELGIUM
Client:: Technum
Main Project Features: 3 nuclear reactors with an installed capacity of 3000 MW
Positions held: Project Manager
Activities performed: Assistance services to the definition of the Thiange nuclear power plant water intake hydromechanical Equipment, Coordination with hydromechanical expert, Project contract, administrative, financial and technical management.
Name of Project: MACAGUA I hydropower plant project
Year: 2010
Location: VENEZUELA
Client:: EDELCA - Electrificacion del Caroni (CARACAS - VENEZUELA)
Main Project Features: 6 vertical Francis turbines, total rated output of 900 MW
Positions held: Design Engineer
Activities performed: Factory Acceptance tests on stator winding bars in Electrozilla’s factory in St Petersburg in Russia
Name of Project: KOUKOUTAMBA hydropower plant project
Year: 2011-2012
Location: GUINEA
Client:: Organisation pour la Mise en Valeur du Fleuve Sénégal (Dakar - SENEGAL)
Main Project Features: 4 vertical Francis turbines, installed capacity 4x73,5MW
Positions held: Design Engineer
Activities performed: Establishment of bidding documents technical specifications and bill of quantities
Name of Project: JIRAU hydropower plant project
Year: 2009 - 2010
Location: BRAZIL, CHINA
Client:: ESBR (Belo Horizonte - BRAZIL)
Main Project Features: horizontal bulb turbines, installed capacity 44x76,5MW
Positions held: Design Engineer
Activities performed: Generators excitation system Factory Acceptance Test in Dong Feng’s factory in Chengdu in China.
Checking of generators drawings and calculation reports.
Name of Project: GURARA Hydropower Plant
Year: 2008 - 2010
Location: NIGERIA
Client:: FEDERAL MINISTRY OF WATER RESOURCES (Abuja - NIGERIA)
Main Project Features: 3 vertical Kaplan turbines, installed capacity 3x30 MW
Positions held: Design Engineer
Activities performed: Supervision of the erection works and units partial commissioning tests
Name of Project: NANGBETO hydropower plant project
Year: 2008
Location: BENIN
Client:: Communauté Electrique du Bénin (CEB)
Main Project Features: Rehabilitation of the generators voltage and speed regulators
Positions held: Design Engineer
Activities performed: Establishment of voltage and speed regulators technical specifications of the tender documents
Name of Project: Manantali hydropower plant project
Year: 2016 - 2017
Location: MALI
Client: Société de Gestion de l’Energie de Manantali (SOGEM)
Main Project Features: 5 vertical Kaplan turbines, installed capacity 5x40 MW
Positions held: Project Engineer
Activities performed: Supervision of overhaul and re-commissioning of units 1,2,4 and 5
Name of Project: Project of the Electricity Sector Strengthening in Ivory Coast (PRSECI) project
Year: March 2015
Location: IVORY COAST
Client: Société des Énergies de Côte d’Ivoire (CI-ENERGIES)
Main Project Features: Supervision and control of Ivory Coast electrical networks strengthening works
Positions held: Project Engineer
Activities performed: Owner’s Engineer:
Name of Project: DEVOLL hydropower plant project
Year: 2014
Location: ALBANIA
Client:: DEVOLL HYDROPOWER (TIRANA - ALBANIA)
Main Project Features: Installed capacity of 39 MW
Positions held: Project Engineer
Activities performed: Factory Acceptance tests on 220kV circuit breaker of Moglicë switchyard in Alstom grid’s factory in Villeurbanne in France
Name of Project: Kaleta hydropower plant project
Year: August 2012 - August 2013
Location: GUINEA CONAKRY
Client:: Administration et Control des Grands Projets (ACGP)
Main Project Features: 3 vertical Francis turbines, installed capacity of 3x70 MW
Positions held: Project Engineer
Activities performed : Technical assistance to the Client
Name of Project: INGA hydropower plant project - FRIPT
Year: 2013
Location: CONGO (DEM. REP.)
Client:: CONGO ENERGIE (KINSHASA - CONGO (DEM. REP.))
Main Project Features: Overhaul of unit G27 and G28, installed capacity 2x174MW
Positions held: Project Engineer
Activities performed: Analysis of bidders’ proposals regarding units electrical systems
Name of Project: SHIRORO hydropower plant project
Year: December 2010 – March 2012
Location: NIGERIA
Client:: Power Holding Company of Nigeria ( PHCN)
Main Project Features: 4 vertical Francis turbines, installed capacity of 4x150 MW
Positions held: Project Manager
Activities performed:
Name of Project: GIBE III Hydropower plant project
Year: 2009 - 2012
Location: ETHIOPIA
Client:: EEPCO (Addis Ababa - ETHIOPIA)
Main Project Features: 10 vertical Francis turbines, installed capacity of 10x187 MW
Positions held: Design Engineer
Activities performed: Technical coordination of the electromechanical experts staff (around 10) in charge of construction drawings approbation
Name of Project: Flood wall of the TIHANGE nuclear power plant
Year: 2011 - 2012
Location: BELGIUM
Client:: Technum
Main Project Features: 3 nuclear reactors with an installed capacity of 3000 MW
Positions held: Project Manager
Activities performed: Assistance services to the definition of the Thiange nuclear power plant water intake hydromechanical Equipment, Coordination with hydromechanical expert, Project contract, administrative, financial and technical management.
Name of Project: MACAGUA I hydropower plant project
Year: 2010
Location: VENEZUELA
Client:: EDELCA - Electrificacion del Caroni (CARACAS - VENEZUELA)
Main Project Features: 6 vertical Francis turbines, total rated output of 900 MW
Positions held: Design Engineer
Activities performed: Factory Acceptance tests on stator winding bars in Electrozilla’s factory in St Petersburg in Russia
Name of Project: KOUKOUTAMBA hydropower plant project
Year: 2011-2012
Location: GUINEA
Client:: Organisation pour la Mise en Valeur du Fleuve Sénégal (Dakar - SENEGAL)
Main Project Features: 4 vertical Francis turbines, installed capacity 4x73,5MW
Positions held: Design Engineer
Activities performed: Establishment of bidding documents technical specifications and bill of quantities
Name of Project: JIRAU hydropower plant project
Year: 2009 - 2010
Location: BRAZIL, CHINA
Client:: ESBR (Belo Horizonte - BRAZIL)
Main Project Features: horizontal bulb turbines, installed capacity 44x76,5MW
Positions held: Design Engineer
Activities performed: Generators excitation system Factory Acceptance Test in Dong Feng’s factory in Chengdu in China.
Checking of generators drawings and calculation reports.
Name of Project: GURARA Hydropower Plant
Year: 2008 - 2010
Location: NIGERIA
Client:: FEDERAL MINISTRY OF WATER RESOURCES (Abuja - NIGERIA)
Main Project Features: 3 vertical Kaplan turbines, installed capacity 3x30 MW
Positions held: Design Engineer
Activities performed: Supervision of the erection works and units partial commissioning tests
Name of Project: NANGBETO hydropower plant project
Year: 2008
Location: BENIN
Client:: Communauté Electrique du Bénin (CEB)
Main Project Features: Rehabilitation of the generators voltage and speed regulators
Positions held: Design Engineer
Activities performed: Establishment of voltage and speed regulators technical specifications of the tender documents
Name of Project: Mali Asset management Director
Year: August 2020 - October 2021
Location: Mali
Client:: EDM S.A.
Main Project Features:50 MWc photovoltaïc power plant in Kita generating around 80 GWh/year into the Malian national Grid
Positions held: Director of the power plant Operation and Maintenance company (Akuo Mali Services)
Activities performed:
© Enersole, Inc.All Rights Reserved.
